Tempering can be performed on AISI 1010 carbon steel, after hardening process is completed, at 316 to 593°C (600 to 1100°F). This depends upon the strength level that is required. When tempering is performed at 538°C (1000 F), the tensile strength will be about 75 ksi. Hardening AISI 1141 Carbon Steel (UNS G11410) - AZoMCarbon steels contain carbon as the primary alloying element. Small quantities of molybdenum, chromium, nickel, aluminium, and copper are also present in these steels. They contain 0.4% silicon and 1.2% manganese. They are designated by AISI four-digit numbers.
Yield Strength Re N/mm 2. Ultimate Tensile Strength Rm N/mm 2. Elongation A 80 min. % DC01-280. 270-410. 28. DC03-240. 270-370. 34. DC04-210. 270-350. 38. DC05-180. 270-330. 40. DC06-180. 270-350. 38. High-strength Steel:EN10268:2006. Yield Strength R e min-max N/mm 2. Ultimate Tensile Strength R m min. N/mm 2. Elongation A 80 min. % HC 260 Cold Rolled Steel Sheet for Drawing EN 10130 DC01 DC064. For design purposes the lower limit of yield strength for DC04 and DC01 may be assumed to be 140 MPa, and for DC05 and DC06 120 MPa. 5. The tensile test is carried out as described in EN 10002 Part 1 using type 2 specimens (initial gauge length Lo = 80mm). Yield strength is determined by the 0,2% off-set method. The test pieces are DC01 Cold Rolled SteelThe grades are classified according to the maximum permissible yield strength and can be subdivided as follows. DC01 This grade can be used for simple forming work, for example Bending, embossing, beading and pulling are used. DC03 This grade is suitable for forming requirements such as Deep drawing and difficult profiles suitable.
Chemical composition of steel DC06 (1.0873), Standards of steel DC06 (1.0873) Mechanical Properties of steel DC06 (1.0873) Equivalent grades of steel DC06 (1.0873) steel DC06 (1.0873) Tensile Strength, Elongation, Proof strength , Hardness DC06+ZN Electro-galvanized steel --- BEBON galvanized DC06+ZN is a kind of electro-galvanized products under the standard EN10271-1998. It is the goods with special deep drawing quality. It is widely used for automobile, household electrical appliances, Office machines, building, manufacturing machine and so on. Datasheet for Steel Grades Structure Steel DC06DC06 DC06 Physical Properties Tensile strength 115-234 b/MPa Yield Strength 23 0.2 /MPa Elongation 65 5 (%) - (%) Akv - Akv/J HBS 123-321 - HRC 30 - DC06 Mechanical Properties Tensile strength 231-231 b/MPa Yield Strength 154 0.2 /MPa Elongation 56 5(%)
Euronorm Structural steel, EN DC06 EN DC06 Physical Properties Tensile strength 115-234 b/MPa Yield Strength 23 0.2 /MPa Elongation 65 5 (%) - (%) Akv - Akv/J HBS 123-321 - HRC 30 - EN DC06 Mechanical Properties Tensile strength 231-231 b/MPa Yield Strength 154 0.2 /MPa EN 10130 Cold Rolled Steel Coil SpecificationEN 10130-DC01 Cold Rolled Coil C P S Mn Ti 0.12 0.045 0.100 0.60 - Yield Strength Mpa Tensile Strength Mpa Elongation(Thickness) 140-280 270-410 28 EN 10130-DC03 Cold Rolled Coil C P S Mn Ti 0.10 0.035 0.035 0.45 - Yield Strength Mpa Tensil EN 10152 Grade DC06 skin passed - Low Carbon Steel - See where EN 10152 Grade DC06 skin passed falls on the material property chart for Density against Elastic modulus in your materials selection and design process. Our Ashby charts are interactive with more technical data upon clicking. Show Low Carbon Steel materials with Yield strength, transverse of 130 - 220 MPa at 20 °C. Thermal.
Aug 07, 2019 · but > 0.5 mm, the maximum yield strength may be 20 MPa higher, and for thicknesses 0.5 mm 40 MPa. 2) or thicknesses 0.7 mm but > 0.5 mm, the minimum elongation at fracture may be 2 units lower. For thicknesses 0.5 mm, the minimum elongation at fracture may be 4 units lower.F 3) The r Information on Aluminium 5754 - thyssenkrupp Materials (UK)Others a):Each:max. 0.05 % Total b):max. 0.15 %. a) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the registration or specification. However, such analysis is not required and may not cover all metallic Other elements. Mild steel > Sheet/coated products - thyssenkruppsmartform ® - cost-optimized forming of high-strength steels without critical springback Tailored Tempering - process for hot forming (partial press hardening) Model and simulation facility Flow-forming machine Welding process for metal active gas welding (MAG)
Specification Yield Strength (N/mm²) Tensile Strength (N/mm²) Elongation(%) Plastic strain ratio r 90 Strain hardening exponent n; Thickness 0.500~ 0.501 SSAB Tunnplat Docol® DC06 (Fe P06) Deep-drawing SteelSSAB Tunnplat Docol® DC06 (Fe P06) Deep-drawing Steel Categories:Metal; Ferrous Metal; Carbon Steel; Low Carbon Steel. Material Notes:Deep-drawing Steel. Comments:Docol - Cold Rolled Mild Steel.Property values are for cold-rolled steel; thicknesses 0.40 - 3.00 mm. Iron content is approximate - exact composition is not reported by the manufacturer. yield strength dc01-Nana party SteelYoung's Modulus - Tensile and Yield Strength for common . Yield strength - y.Yield strength is defined in engineering as the amount of stress (Yield point) that a material can undergo before moving from elastic deformation into plastic deformation.Yielding - a material deforms permanently; The Yield Point is in mild- or medium-carbon steel the stress at which a marked increase in deformation
Tensile Strength . Yield Strength max . Elongation min. r. n <0.70. 0.70-<1.0. 1.0-<1.6 >=1.6. min. min. DC06. 270-330. 170. 39. 40. 41. 42. 2.1 . 0.22